Delta-electronics Terminal Panels Series TP02G-AS1 Manual de usuario descargar pdf

Warning

 Please read this instruction carefully before use.

 Switch off the power before wiring.

 The display panel of TP02 series is waterproof. But please prevent grease, corrosive liquids and sharp objects from

contacting the TP02 series.

 The TP02 series require 24V DC input power. DO NOT connect input AC power supply to any of the RS-485

communication port; otherwise serious damage may occur. Check all the wiring again before switching on the

power.

 DO NOT touch any terminal when the power is switched on. DO NOT touch any internal circuit in 1 minute after

the power is switched off.

 Make sure the groud terminal is correctly grounded in order to prevent electromagnetic interference.

 Please use the fixed support accessory which is packed together with the product provided by Delta. DO NOT

tighten the screws out of the normal torque specifications; otherwise serious damage may occur.

 Introduction





 Product Outline

Display ing Area

RS-232 LED Indicator

RS-485 LED Indicator

Escape / Exit Key

Alarm LED Indic ator

Function Keys

Arrow Keys

Enter Key





 Panel Function Explanation

Panel component

Explanation

Alarm LED

indicator (RED)

Status 1: When power is on, LED will blink slowly for three times.

Status 2: When there is an abnormal situation, LED will blink quickly along with an alarm sound.

RS-232 LED

indicator (yellow)

LED will blink when transmits program and communicates via RS-232.

RS-485 LED

indicator (green)

LED will blink when communicates via RS-485.

Displaying area Liquid Crystal Module display area. It is used to display current program status.

Escape/Exit key It is used to cancel an incorrect input, or to exit a programming step.

Enter key It is used to input a value or accept a programming command.

Arrow keys

UP/Pg Up: It is used to increase the value or move up one page.

Pg Dn/DOWN: It is used to decrease the value or move down one page.

Left: This key is left direction key and it can be used to select the position of the value.

Right: This key is right direction key and it can be used to select the position of the value.

Function keys

F0/0: It is used as a constant 0, or the user can define it as function F0.

F1/1: It is used as a constant 1, or the user can define it as function F1.

F2/2: It is used as a constant 2, or the user can define it as function F2.

F3/3: It is used as a constant 3, or the user can define it as function F3.

F4/4: It is used as a constant 4, or the user can define it as function F4.

F5/5: It is used as a constant 5, or the user can define it as function F5.

F6/6: It is used as a constant 6, or the user can define it as function F6.

F7/7: It is used as a constant 7, or the user can define it as function F7.

F8/8: It is used as a constant 8, or the user can define it as function F8.

F9/9: It is used as a constant 9, or the user can define it as function F9.

ENGLISH





 Back Panel

RS-232

Extension port

5 PIN terminal/Wire gauge: 12-24 AWG/Torque: 4.5 lb.-inch





 Dimension

Front panel (unit: mm [inch]) Right side diagram (unit: mm [inch])

Vertical view (unit: mm) Mounting dimension (unit: mm [inch])

Thickness Range 0.5~9mm

135~136.5[5.31~5.37]

[3.35]





 Installation

Please insert TP02 series to the opening hole of panel and tighten the screws. However, if a firm mounting

TP02 series to the panel is needed, please use the mounting fixed support accessory which is packed together

with TP02 series, then insert the fixed support in the back and tighten the screws.

If the fixed support is not installed well, Delta will not guarantee the waterproof function. The screw torque

should be 4-5(kg-cm). DO NOT exceed this specification when tightening the screws; otherwise TP02 series

may be damaged. Please leave sufficient space (more than 50mm) around the unit for heat dissipation.

Notes: The flat surface should be a UL Type 4 "Indoor Use Only" enclosure or equivalent (IP65/NEMA4). Please refer to

the figures below.

Thickness: 0.5~9.0mm



Specifications





 Function Specifications

Item TP02G-AS1

Screen type STN-LCD

Display color Monochromatic

Backlight

The back-light automatic turn off time is 1 ~ 99 minutes (0 = DO NOT turn off)

(The back-light life is about 50 thousand hours at 25°C)

Resolution 160 x 32 dots

5×8 dots, 25 characters×8 rows

8×8 dots, 16 characters×8 rows

8×12 dots, 16 characters×5 rows

8×16 dots, 16 characters×4 rows

Display range (W) x (H) = 72 x 22 (unit: mm)

Contrast adjustment

15 levels of adjustment

Language/font

ASCII: Alphanumeric (including European characters)

Taiwan: (Big 5 codes) Traditional Chinese Fonts

China: (GB2324-80 codes) Simplified Chinese Fonts

Font size ASCII: 5 × 8, 8 × 8, 8 × 12, 8 × 16

Alarm LED indicator

(RED)

1. Power on indication (blink for three times)

2. Communication error alarm

3. Special indication by user programming

RS-232 LED

indicator (yellow)

It will blink when transmitting program and communicating by using RS-232.

Display

screen

RS-485 LED

Indicator (green)

It will blink when communicating by using RS-485.

Program memory 256KB flash memory

RAM of system 32K Byte

Serial

communication port

RS-232 (COM1)

Unsynchronized transmission method: RS-232

Data length: 7 or 8 bits, Stop bits: 1 or 2 bits

Parity: none/odd/even, Transmission speed: 4,800 bps ~115,200 bps

RS-232: 9 PIN D-SUB male

Extension

communication port

RS-485 (COM2)

Unsynchronized transmission method: RS-485

Data length: 7 or 8 bits, Stop bits: 1 or 2 bits

Parity: None/Odd/Even, Transmission speed: 4,800 bps ~115,200 bps

RS-485: 5 PIN removal terminal

Extension interface 1. Update firmware version

2. The slot for program copy card

External

interface

5 PIN removal

terminal

Include 24V DC input and RS-485 communication input





 Electrical Specifications

Specifications TP02G-AS1

Communication interface COM1: RS-232 COM2: RS-485

Waterproof class of front panel IP65/NEMA4

Operating temperature for

hardware

0 ~ 50°C; 20 ~ 90%RH (non-condensing)

Specifications TP02G-AS1

Storage temperature for

hardware

-20 ~ 60°C

Vibration

5Hz f 9Hz = Continuous: 1.75mm / Occasional: 3.5mm

9Hz f 150Hz = Continuous: 0.5g / Occasional: 1.0g

Shock

15g peak, 11ms duration, half-sine, three shocks in each direction per axis,

on 3 mutually perpendicular axes (total of 18 shocks)

Radiated emission CISPR11, Class A

Electrostatic discharge immunity

EN61000-4-2

Radiated immunity EN61000-4-3

Electrical fast transient EN61000-4-4

Weight/dimensions 0.24kg; 147 × 97 × 35.5mm (Width(W) × Height(H) × Deep(D))

Cooling method Natural air cooling

 Password Function

1. If the user forgot the password, the password can be cleared by using the following code: 8888. This

universal code will clear the password and all TP02 series internal programs. The TP02 series will be reset to

the factory settings by using this code also. Please pay close attention when using it.

2. The password can be the alphabet from A to Z or the number from 0 to 9. But it must use the function keys F0

~ F9 to input the password characters. Please refer to the following table.

F0: scrolls in a loop as follows 0→A→B→C→D→E→F→0.

F1: scrolls in a loop as follows 1→G→H→I→J→K→1.

F2: scrolls in a loop as follows 2→L→M→N→O→P→2.

F3: scrolls in a loop as follows 3→Q→R→S→T→U→ V→3.

F4: scrolls in a loop as follows 4→W→X→Y→Z→4.

F5: It just can be used to be constant 5.

F6: It just can be used to be constant 6.

F7: It just can be used to be constant 7.

F8: It just can be used to be constant 8.

F9: It just can be used to be constant 9.

 Hardware Operation

When the user wants to startup TP02 series, a 24V DC power is needed. After applying 24V DC power to TP02

series, it will enter into the startup display and then enter the user-designed program. Pressing Esc key and

holding on for 5 seconds can return to system menu. There are five selections in the system menu and are

described below.

Selections Explanation

Download

program

Use the connection cable (DVPACAB530) to connect the TP02 serial communication port RS-232 to a

PC. Then use the TPEditor software to download an application program to TP02.

Upload program

Use the connection cable (DVPACAB530) to connect the TP02 serial communication port RS-232 to a

PC. Then use the TPEditor software to upload an application program from TP02.

Copy program

Transfer a program between two TP02 units.

1: transmit programs; 2: receive programs.

When transmit programs and data between two TP02 units. Set one TP02 to “Receive Program”

mode and the other TP02 to “Transmit Program” mode. Please use twisted pair wires to connect the

two units via the RS-485 ports.

Selections Explanation

TP02 settings

There are 8 items that used to modify TP02 system settings:

1. Communication protocol: Setting the address of TP02, the control port of PLC, and the

communication string for either RS-232 or RS-485.

2. Contrast: Adjust the contrast of LCM display screen.

3. Back-light: adjust the automatic turn off time of LCM. Setting range is 00 ~ 99 minutes. If set to 00,

the LCM Back-light will not turn off.

4. Buzzer: Used to set the buzzer sound, normal mode or quiet mode.

5. Language setting: Used to set the displayed language. English, Traditional Chinese, Simplified

Chinese or user defined language.

6. Password setting: Used to set, enable, and disable the password function. If the password function

is enabled, it will require the user to input a password before entering any system menu. The

factory password is 1234.

7. Startup display: Used to select the TP02 startup display. User can select “user defined” to use the

file that designed by TPEditor and download to TP02.

8. Comm. indicator: The user can determine if the RS-232 and RS-485 LEDs will blink or not during

communication.

PLC connection

There are two methods to connect to PLC:

1. Using TP02 serial communication port (COM1) RS-232: set 8-pin DIP switch to RS-485 mode and

connect the cable (DVPACAB215 or DVPACAB230) to program communication I/O RS-232C of

PLC.

2. Using extension communication port (COM2) RS-485: set 8-pin DIP switch to RS-485 mode and

connect 5-pin removal terminal of extension communication port to RS-485 of PLC with twisted

pair.

Execution

Execute the internal program that download from TPEditor or transmitted from other TP02 units.

When program is in execution, the user can return to system menu by pressing Escape/Exit (Esc) key

for 5 seconds.

 Communication Connection





 TP02G may connect to a PC by using connection able DVPACAB515

PC or TP 02 / 04G

9 PIN D-SU B

TO PC (R S- 2 32)

TO TP02 / 04G

9 PIN D- SU B

9 PIN D- S UB fem ale

Rx 2

GND 5

5 GND

PC COM Port

9 PIN D- S UB fem ale

3 Tx

2 Rx

TP 02 / 04G C O M Port

Tx 3





 TP02G may connect to a DVP-PLC by using connection cable DVPACAB215/DVPACAB230/

DVPACAB2A30

DVPACAB215/DVPACAB230

TO P C o r TP 02 / 04G

25 P I N D-S U B

9 P IN D- SU B

TO P LC

M I N I D I N TERM I N AL

DVPACAB2A30

TO PC or TP0 2 / 04G

9 PI N D -SU B

TO PLC

MIN I DIN TER MINAL

8 P I N M INI D IN

25 PIN D-SU B fem a l e

PC / TP C O M Port PLC C O M1 P ort

GN D 7

8 PIN MIN I DIN9 P I N D -SUB f e m a l e

PC / TP C OM Port

PLC C O M1 P ort

R x 2

GN D 5

4 R

8 G ND

1,2 5V

5 Tx

Rx 3

Tx 3

4 R

8 G ND

1,2 5V

5 T x



 24V RS-485







LC M

RS-23 2

RS-48 5



RS-232

RS-485 RS-485

UP/Pg Up

Pg Dn/DOWN

Left

Right

F0/0 0 F0

F1/1 1 F1

F2/2 2 F2

F3/3 3 F3

F4/4 4 F4

F5/5 5 F5

F6/6 6 F6

F7/7 7 F7

F8/8 8 F8

F9/9 9 F9



RS-232

5-Pin / 12-24 AWG / 4.5 lb-inch



( mm)

97.00 [3.82]

147.00 [5. 79]

( mm)

3.50 [0.14]

30.50 [1.20]

135.05 [5.31]

40.50 [1.59]

( mm) ( mm)

85.00 [3.35]



4-5 (kg-cm)

Type 4

1 2

Indice de contenidos

Pagina 1 - 147.00 [5. 79]

Warning  Please read this instruction carefully before use.  Switch off the power before wiring.  The display panel of TP02 series is waterpro

Pagina 2 - ON TP04G

0. 5 ~9. 0 m m   TP02G-AS1 STN-LCD 1 ~ 99 0 25°C 5 16032 58 258 88 168 812 165 816 164 72mm (W)  22mm (H) 15

Comentarios a estos manuales

Sin comentarios

Delta-electronics Terminal Panels Series TP02G-AS1 Manual de usuario

Busca en linea o descarga Manual de usuario para Accesorios De Computador Delta-electronics Terminal Panels Series TP02G-AS1. Delta Electronics Terminal Panels Series TP02G-AS1 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios De Computador Delta-electronics Terminal Panels Series TP02G-AS1