Delta-electronics AC Servo Drive ASDA-B Manual de usuario Pagina 264
- Pagina / 321
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 10 Troubleshooting|ASDA-B Series
Revision February 2008, Doc. Name: 2006PDD23000009 10-9
Keypad Fault Messages
ALE 30 : LCM hardware error
Potential Cause Checking Method Corrective Actions
No display Check if the 4th Pin of LCM is normal.
Please contact your distributor for
assistance or contact with Delta.
Error characters
display.
Check if the related Pins is short-circuited and
check if IC operation is normal.
Please contact your distributor for
assistance or contact with Delta.
ALE 31 : LED hardware error
Potential Cause Checking Method Corrective Actions
Check if LED is normal.
Please contact your distributor for
assistance or contact with Delta.
LED indicator is
abnormal.
Check if the transistor is abnormal and check if
IC operation is normal by setting P8-09 to 2.
Please contact your distributor for
assistance or contact with Delta.
ALE 32 : KEY hardware error
Potential Cause Checking Method Corrective Actions
The function key is
disabled.
Check if IC operation is normal by setting P8-
09 to 1.
1. Activate P8-09 to perform the
testing.
2. Please contact your distributor
for assistance or contact with
Delta.
ALE 33 : RAM hardware error
Potential Cause Checking Method Corrective Actions
LCM display is
abnormal.
In regular condition, disorganized display or
abnormal display shows on LCM. Please check
if the working voltage of RAM is normal.
1. Activate P8-09 to perform the
testing.
2. Please contact your distributor
for assistance or contact with
Delta.
Function key is
abnormal.
Check if the transistor is abnormal and check if
IC operation is normal by setting P8-09 to 3.
1. Activate P8-09 to perform the
testing.
2. Please contact your distributor
for assistance or contact with
Delta.
ALE 34 : EEPROM hardware error
Potential Cause Checking Method Corrective Actions
Store data error
Check if the operation of MCU or EEPROM is
normal by setting P8-09 to 4.
1. Activate P8-09 to perform the
testing.
2. Please contact your distributor
for assistance or contact with
Delta.
- 20080227 1
- Preface 2
- Table of Contents 6
- 1.2 Model Explanation 16
- 1.2.1 Nameplate Information 16
- ASDA-B Series Servo Drive 17
- ECMA Series Servo Motor 18
- Minimum Clearances 25
- Side by Side Installation 25
- 3.1 Connections 26
- 3.1.3 Wiring Methods 29
- 3.2 Basic Wiring 34
- Digital output 37
- Max. input pulse 46
- 3.4 Encoder Connector CN2 49
- CN3 Drive Connector 50
- Notebook 51
- 3.6.1 Position Control Mode 52
- 3.6.2 Speed Control Mode 53
- 3.6.3 Torque Control Mode 54
- 4.1 ASD-PU-01A 56
- 4.1.2 Display Flowchart 58
- FEDIT:AUTO D -L 61
- 6 61
- Fast Editing 62
- Dynamic Auto-tuning 62
- Static Auto-tuning 62
- 4.1.5 JOG Operation 67
- DI1: OFF 70
- 4.2 ASD-PU-01B 73
- Figure 4.9 75
- Figure 4.11 79
- 4.2.5 JOG Operation 86
- 5.1 Inspection without Load 94
- 5.5.1 Tuning Flowchart 106
- KVI (Parameter P2-06) 113
- NLP (Parameter P2-25) 114
- 6.2 Position Control Mode 117
- Encoder PPR: 2500 pulse 120
- Ball Screw Pitch: 3mm 120
- Workpiece (Table or Load 120
- 6.2.5 Low-pass Filter 121
- Position 123
- 6.3 Speed Control Mode 124
- Ta r ge t S p ee d 128
- Time Domain 136
- Motor Speed 137
- Inertia Measurement 137
- 6.3.7 Resonance Suppression 138
- Gain (db) 138
- Frequency (Hz) 138
- 6.4 Torque Control Mode 140
- Ta rge t S pee d 142
- 6.5 Control Modes Selection 144
- 6.6 Others 146
- 6.6.1 Speed Limit 146
- 6.6.2 Torque Limit 146
- 6.6.3 Regenerative Resistor 147
- 6.6.4 Electromagnetic Brake 151
- Chapter 7 Servo Parameters 154
- 7.2 Parameters Summary 155
- Basic Parameters 156
- Extension Parameters 158
- Communication Parameters 160
- Diagnosis Parameters 161
- Keypad Parameters 162
- Monitor and General Use 163
- Gain and Switch 164
- Position Control 165
- Digital I/O 167
- Communication 168
- Communication Addr.: 0416H 219
- Communication Addr.: 0417H 219
- Controller 220
- Code Description: 243
- Data Format: 243
- Communication Protocol: 244
- 9.1 Basic Inspection 252
- Cooling fan 254
- Chapter 10 Troubleshooting 256
- Chapter 11 Specifications 268
- 269
- 11.7 EMI Filters Selection 289
- PLC Program 291
- HMI DOP-A HMI 296
- (Position Control 1) 297
- (Position Control 2) 298
- (JOG Operation) 299
- Connecting to Delta DVP-01PU 305
- Appendix A Accessories 310
- (100 mm) 312
- (3.15 inch) 312
- (3.94 inch) 312
Relacionado con productos y manuales para Hardware Delta-electronics AC Servo Drive ASDA-B
(8 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales